How to use ffmpeg to cut video
How to use ffmpeg to cut video movie#
Convert an AVI movie file to MP4 with AAC audio codec and x264 video codec:įfmpegtranscode('input.avi', 'output.mp4', 'AudioCodec', 'aac', 'VideoCodec', 'x264') Įxample 2. Note that if a newer version of FFmpeg is placed elsewhere on the PC, you must rerun ffmpegsetup to specify which ffmpeg executable is used with the toolbox.Įxample 1. In MATLAB, run the toolbox setup m-file (ffmpegsetup.m) and follow its instructions. (E.g., in Windows, ffmpeg.exe must be available). To use this toolbox, FFmpeg binaries must already be downloaded and made available on the PC. While FFmpeg supports a vast number of multimedia formats and codecs, FFmpeg Toolbox brings a selected few (MP3, AAC, mpeg4, x264, animated GIF) closer to the user with its output option parameters. FFmpeg Toolbox is aimed to bring FFmpeg features to Matlab. Inverse Fourier Transform of an Image with low pass filter: cv2.FFmpeg ( ) is a complete, cross-platform solution to record, convert and stream audio and video.
Signal Processing with NumPy II - Image Fourier Transform : FFT & DFT Signal Processing with NumPy I - FFT and DFT for sine, square waves, unitpulse, and random signal OpenCV 3 image and video processing with Python The core : Image - load, convert, and save
How to use ffmpeg to cut video free#
Sponsor Open Source development activities and free contents for everyone. Here is the video after cutting off head and tail sections: "Here, the first command will cut from 00:01:00 to 00:03:00 (in the original), whereas the second command would cut from 00:01:00 to 00:02:00, as intended." "Note that if you specify -ss before -i only, the timestamps will be reset to zero, so -t and -to have the same effect:"įfmpeg -ss 00:01:00 -i video.mp4 -to 00:02:00 -c copy cut.mp4įfmpeg -i video.mp4 -ss 00:01:00 -to 00:02:00 -c copy cut.mp4 Or you can use the -to option to specify an out point, like -ss 60 -to 70 to capture from second 60 to 70. "To extract only a small segment in the middle of a movie, it can be used in combination with -t which specifies the duration, like -ss 60 -t 10 to capture from second 60 to 70. The explanation for the parameters is well describe in /wiki/Seeking with FFmpeg: Since it's just making a copy, it's quick. It has 4:11 running time, but I want to cut off from 0 to 7.5 second, and chop off the tail from 4:05 to then end.įfmpeg -i yellowstone.mp4 -ss 00:00:07.5 -to 00:04:05 -c copy yellowstone_cut.mp4 I want the cut off head and tail section of the video. Your browser does not support the video tag. In this chapter, we'll play with the following video:
The result should be the same as in "Accurate seeking" section, only a lot faster." This is where it stops at the last keyframe found (somewhere before 00:02:30, depending on the GOP size/keyframe interval of the input) and then it will slowly seek the next 00:00:30 seconds to the desired time point. This works because ffmpeg will first seek by keyframes, until it reaches 00:02:30. Then we slow down and seek frame by frame to the third minute. We first seek very fast somewhere before the third minute. "This approach is combining the best characteristics of both fast and accurate ways of seeking in ffmpeg. The parameter -ss can be used to seek into the input video.Īs described in my another FFmpeg chapter ( Thumbnails), there are differences in seek time it takes and in the accuracy of the extraction time, depending on the order of the two parameters ( -i and -ss) in the ffmpeg command.Īctually, Seeking with FFmpeg recommends using -ss twice before and after -i to get faster and accurate output.įfmpeg -ss 00:02:30 -i video.mp4 -ss 00:00:30 -frames:v 1 out.png If we want only a specific part of our video input, first of all, we need to use the seeking option to get to that specific part.